To access an Amped Wireless range extender, you must first connect your phone, tablet, or PC to the extender's Wi‑Fi network, then open a web browser and go to setup.ampedwireless.com. This direct method is the only way to reach the web‑based setup page, there is no iPhone or Android app for configuration.
How to access your amped wireless range extender
There are two direct methods to reach the web‑based setup page. The primary method is to open a browser and enter setup.ampedwireless.com. If that page does not load, use the fallback IP address 192.168.1.240 instead. Before either method works, your device must be connected to the extender’s own Wi‑Fi network, not your main router’s network.
Step-by-step setup instructions
- Plug in the range extender and attach the antennas if your model includes them.
- Connect your phone, tablet, or PC to the extender’s Wi‑Fi network. The default SSID is often
Amped_REC10or similar. One setup guide says to connect to the extender SSID Amped_REC10 first. - Open a web browser on that device.
- In the address bar, type
setup.ampedwireless.comand press Enter. - If the setup page does not appear, type
192.168.1.240in the address bar instead. - In the setup wizard, click or select Scan, choose the Wi‑Fi network you want to extend, and enter that network’s security key when prompted.
- After the extender connects, reconnect your device to the new extended network (the extender’s network) to complete the process.
This browser‑based procedure works with any PC, tablet, or smartphone that has Wi‑Fi and a web browser. No app download is required.
Placement and signal strength requirements
For reliable setup, place the extender no more than halfway between your Wi‑Fi router and the dead zone you want to cover. The extender’s setup wizard requires a Wi‑Fi signal strength of 70% or greater from your router. If no networks appear during scanning or the signal strength is below 70%, move the extender closer to the router and rescan. Proper placement is critical, if the extender is too far from the router, it cannot receive a strong enough signal to extend.
Troubleshooting access problems
If the setup page will not load, try these solutions in order:
- Try the fallback IP: Enter
192.168.1.240in the browser instead ofsetup.ampedwireless.com. - Use a different browser: Switch to another browser on your device.
- Connect via Ethernet: Temporarily connect your computer directly to the extender using an Ethernet cable, then try the browser again.
- Check power and connections: Confirm the extender is plugged in, powered on, and that all cables are secure.
- Reset the extender: Press and hold the Reset button on the extender for 5 to 10 seconds (some guides say 10 seconds) until the LEDs flash, then release. After resetting, reconnect to the extender’s Wi‑Fi and try accessing the setup page again.
Also ensure your computer is not connected to any other Wi‑Fi network while troubleshooting, disconnect from your main router’s Wi‑Fi so your device is only connected to the extender. One FAQ says to make sure the computer is not connected to any Wi‑Fi networks when troubleshooting browser access and to use Ethernet to the extender if needed. Verify network compatibility: one support page lists setup requirements as wireless 802.11a/b/g/n or ac, on 2.4 GHz or 5 GHz networks, with a computer, tablet, or smartphone that has Wi‑Fi and a web browser.
Frequently Asked Questions
What are the default login credentials for the setup page?
The default username and password for most Amped Wireless range extenders is “admin” for both fields. Check your specific model’s manual if these do not work.
Can I use multiple Amped Wireless range extenders on the same network?
Yes, you can use multiple extenders in a daisy‑chain setup. Connect the primary extender to your router, then place additional extenders within range of the previous one to extend coverage further.
What should I do after setup is complete?
After the setup wizard finishes, reconnect your device to the new extended network. You can then place the extender in its final location (still no more than halfway between the router and the dead zone) and verify the signal strength is 70% or greater.
For the wider topic, see connect wireless extender.
